Selecting an injection mould starts with understanding the part itself and the quantity required. Review the component geometry, dimensional tolerances, visible surface finish, projected shot volume, and production schedule before deciding on the mould structure. For programmes ranging from 50,000 to 1,000,000 shots, the planned output should be compared with the supplier's stated mould-life range and validated through trial moulding and dimensional checks.
A practical mould specification should translate the product requirements into clear tooling decisions. Start with the part's shape, wall sections, undercuts, appearance requirements, and critical dimensions. Then document the expected number of shots, delivery schedule, quality standards, and preferred inspection process.
The available mould configurations include single- and multi-cavity designs, SPI or VDI surface finishes, and an optional hot runner system. The supplied product information does not establish a universal cavity-count formula or identify one configuration as suitable for every part. The final arrangement should therefore be reviewed against the actual component, projected demand, machine capacity, and required cycle time.
Listed mould-base materials include S50C, P20, and 1.2738, while H13 and 718H are identified as mould-steel options. The quoted mould-life range is 50,000–1,000,000 shots. This range should be treated as a reference for discussion rather than a guaranteed result, because tool life can vary with the material being moulded, operating conditions, maintenance, mould complexity, and production practices.
Quality planning should include IQC incoming inspection, mould trial testing, dimensional inspection, and a complete inspection before shipment. Agree in advance on trial samples, critical measurements, appearance standards, and sample approval. Longterm also lists mould-maintenance guidance, spare-parts support, online technical assistance, and after-sales consultation.
Longterm reports project experience involving an electronic housing mould for a handheld device and a double-shot overmoulding project for a consumer electronics shell. The project feedback refers to dimensional control, surface quality, alignment, trial samples, and delivery performance. These examples demonstrate reported experience, but they do not define the mould design or production quantity required for another customer's part.
| Selection factor | Available information | How to apply it |
|---|---|---|
| Projected output | Stated mould life of 50,000–1,000,000 shots | Compare the planned shot count with this range and confirm the expected service life for the specific project. |
| Cavity arrangement | Single-cavity or multi-cavity | Assess part size, output targets, machine capacity, cycle time, and investment with the mould supplier. |
| Mould base | S50C, P20, or 1.2738 | Confirm which listed base material meets the design, durability, and project requirements. |
| Mould steel | H13 or 718H | Review the steel choice in relation to the resin, wear, temperature, expected volume, and maintenance plan. |
| Surface and runner system | SPI or VDI finish; hot runner optional | Specify the required appearance and determine whether a hot runner supports the gate design and production objectives. |
| Quality verification | Mould trial, dimensional inspection, and final inspection | Set inspection criteria and sample-approval requirements before the tool enters production. |
How can I compare mould life with my production forecast?
Estimate the total number of shots required over the planned production period and compare that figure with the stated range of 50,000–1,000,000 shots. Ask the supplier to confirm the expected life for your part, resin, operating conditions, and maintenance schedule.
When is a multi-cavity mould worth considering?
A multi-cavity layout may support higher output, but the correct choice depends on the part design, machine capacity, cycle-time target, balancing requirements, and tooling budget. The supplied product data supports both single- and multi-cavity options without prescribing one for every application.
What should be checked before the mould is shipped?
The listed checks include IQC incoming inspection, mould trials, dimensional inspection, and full inspection before shipment. Trial samples and formal approval criteria can be included in the project quality plan.
The most reliable way to choose an injection mould is to connect the part requirements with the intended production volume. Prepare a tooling brief covering geometry, tolerances, finish, shot count, cavity layout, material options, runner system, and inspection expectations. Longterm lists a minimum order quantity of one set and an estimated delivery time of 20–35 days, with export markets including Europe, North America, and Australia.
The company profile describes mould design and manufacturing, precision machining, and parts production, supported by ISO 9001:2015 certification. For technical enquiries or project support, contact Roger Luo at rogerluo@longterm-mold.com.
Longterm Manufacturing Solutions Limited was founded in 2010 and serves customers in the United States, Europe, Australia, and other international markets. The company reports a team of 50 employees and provides mould design, tooling, precision machining, mould manufacturing, and parts production. Its ISO 9001:2015 certification covers the design, manufacturing, and sales of precision moulds and the sales of plastic products; its project examples span consumer electronics, home appliances, and industrial parts.

REPORT