Before approving a large order of RGB laser projectors, evaluate the sample against the exact requirements of the final installation. The inspection should cover optical output, color wavelengths, beam quality, scanning speed, control interfaces, safety responses, weather resistance, operating endurance, and production consistency. A complete sample test helps confirm that the selected projector can perform reliably at outdoor concerts, festivals, clubs, architectural sites, and other entertainment applications.
The projector uses an imported semiconductor solid-state RGB laser source with analog modulation. Available configurations are listed as 50W, 60W, and 80W. During sample approval, measure the actual output of the red, green, and blue channels and record the results as a reference for mass production.
The specified color wavelengths are red at 636±5nm, green at 525±5nm, and blue at 455±5nm. Inspect the aperture and optical path for a beam size below 8*9mm and beam divergence below 1.2mrad. Check whether the beam remains even and well-defined while changing colors, patterns, and effects. Output should remain stable rather than fluctuate during extended use.
The scanning system is rated at 25KPPS high-speed scanning. Test geometric accuracy, movement smoothness, pattern definition, and the consistency of projected effects at different scan angles and speeds. Include a long-duration run in the acceptance procedure. Stable operation over many hours is particularly important for stage productions, concerts, and rental projects where the projector may operate continuously.
Evaluate each control option included in the specification. The sample provides RJ45 and ILDA DB25 interfaces and is designed to support international-standard ILDA control, DMX512 operation, self-walk programs, and master-slave synchronization. Connect the projector to the actual control equipment planned for the project and verify that patterns, colors, movement, intensity, and effect changes respond correctly.
Where applicable, test compatibility with Pangolin software and tiger, pearl, or MA controllers. Do not rely only on a successful connection: check communication stability during continuous playback and confirm that all required functions are available in the selected control mode.
Safety behavior must be tested separately. Remove or interrupt the control signal and confirm that the light closes as specified. Verify the listed no-signal protection and one-beam protection functions, and document the response time and recovery behavior. Any difference between the sample's safety performance and the agreed specification should be resolved before production begins.
For outdoor projects, inspect the housing, seals, connectors, and cable entries in addition to reviewing the stated IP66 rating. Request the supplier's waterproof and safety testing records, and confirm that the sample is appropriate for the temperature, humidity, dust, and installation conditions expected at the venue.
The documented inspection process includes laser module inspection, optical performance verification, scanner system testing, electronic component inspection, control system testing, aging tests, finished-product inspection, and pre-shipment inspection. Ask for the relevant records and make sure the same configuration and quality requirements will apply to the bulk production run.
Check the physical condition of the projector and its flight case. Confirm that power cables, control cables, mounting or installation accessories, manuals, and any required software or adapters are included. Record serial numbers and photograph the approved configuration so the delivered units can be compared against the sample.
NewFeel Lighting holds CE certification for laser light under certificate number UTT202406076C, with applicability listed as worldwide. The company has also supplied RGB laser lights, fog machines, and special-effects equipment to a lighting equipment distributor in the United States for wedding events, private parties, DJ performances, and small entertainment venues.
| Inspection Category | Items to Test | Acceptance Target |
|---|---|---|
| Optical output | RGB power, wavelengths, analog modulation, beam size, and divergence | Measured results match the ordered specification |
| Scanning system | 25KPPS speed, pattern accuracy, movement, and long-run stability | Clear, smooth, and consistent effects during operation |
| Control integration | RJ45, ILDA DB25, ILDA, DMX512, self-walk, and master-slave modes | All required control routes operate with the planned equipment |
| Safety response | No-signal shutdown and one-beam protection | Protective functions activate and recover as documented |
| Environmental protection | IP66 enclosure, sealing, connectors, and waterproof test documentation | Suitable for the intended outdoor location |
| Order readiness | Flight case, accessories, inspection records, aging test, and configuration | Bulk units will match the approved sample |
Measure the selected laser power, red, green, and blue wavelength output, beam size, beam divergence, and analog modulation behavior. The stated options are 50W, 60W, or 80W, with wavelengths of 636±5nm red, 525±5nm green, and 455±5nm blue. The listed beam size is below 8*9mm and divergence is below 1.2mrad.
Connect the sample to the control systems that will be used in the project and test ILDA, DMX512, self-walk, and master-slave functions. Where relevant, verify operation through Pangolin software and tiger, pearl, or MA controllers. Check both normal playback and communication recovery after signal interruption.
The stated minimum order quantity is one unit. Sample orders are listed at 7–15 working days, while bulk orders are listed at 20–35 working days after order confirmation. Customized laser systems may require additional time according to the configuration and project scope. Available support includes technical consultation, setup instructions, software configuration, installation assistance, troubleshooting, and spare-parts service.
A bulk purchase should be approved only after the sample passes optical, scanning, control, safety, waterproof, aging, and extended-operation evaluations. Keep a written test record containing measured values, accepted accessories, software and controller results, safety responses, and the final production configuration. This provides a practical reference for incoming inspection and reduces the risk of receiving units that differ from the approved sample.
Guangzhou New Feel Lighting And Audio Equipment Co., Ltd. integrates R&D, manufacturing, sales, export, OEM/ODM, and customized stage-lighting services. Its stated monthly production capacity is approximately 5,000 professional lighting units. For project-specific technical consultation or support, contact sunny@nfstagelight.com.
Guangzhou New Feel Lighting And Audio Equipment Co., Ltd., known as NewFeel Lighting, was founded in 2008 in Guangzhou, China. The manufacturer supplies RGB laser projectors, outdoor laser systems, moving head lights, fog machines, snow machines, and professional stage-effects equipment for concerts, festivals, weddings, clubs, entertainment venues, rental productions, and architectural lighting projects. Its R&D capabilities cover optical design, electronic control, structural optimization, and customized product development. The company reports a factory capacity of approximately 5,000 or more lighting units per month, while its CE-certified laser products and industry cooperation cases support customers in multiple markets.

REPORT